 
化石会员
精华11
帖子2111
注册时间2007-8-1
在线时间4814 小时
最后登录2018-1-7
好友4
|
在 Using the Canon EOS 10/10s - an unofficial manual（佳能 EOS 10/10s - 非官法手册） - http://photonotes.org/manuals/eos-10s/ 中有关于所谓CF(Custom Functions, 自定义功能）操作的描述：
===========================================
Custom functions.
The 10/10s has 14 (the 10QD has 15) user-configurable settings which Canon calls “custom functions.” Press the blue and yellow bottom plate buttons together simultaneously to enter custom feature mode. Use the main dial to go between the numbered functions. Press the round partial metering button on the back to switch between N (no, for off) and Y (yes, for on) for each custom function. If you have one or more custom functions set to something other than the default then the CF icon appears on the top deck LCD. Somewhat uselessly, as it doesn’t tell you which CFs have been set.
Remember that many of these custom functions are ignored if you use the camera in one of the PIC modes for fear of confusing beginners.
1. Film rewind mode.
N - Enables automatic rewind at the end of the roll.
Y - Rewinds only after you push the film rewind button.
2. Film leader position:
N - Rewinds the film all the way into the cartridge.
Y - Leaves the film leader protruding outside the cartridge.
3. Film speed setting:
N - Automatic DX code setting. (ie: reads the film canister DX code when film is loaded and sets the ISO speed accordingly)
Y - Manual film-speed setting of DX-coded film. (ie: ignores the DX coding and uses whatever ISO setting the camera is currently set to when you load a film canister. The camera will briefly display the current ISO setting on the topdeck LCD when you load the film)
4. AF start:
N - Normal operation. ie: pressing the shutter release halfway down engages AF.
Y - Initiates autofocus by pressing the partial metering button - the round button on the right-hand side of the camera back.
5. Manual exposure in M mode:
N - Shutter speed set by main dial and aperture set by partial metering button plus main dial.
Y - Reverse. (aperture set by main dial and shutter speed set by partial metering button plus main dial.)
6. Shake warning beeper. The manual incorrectly says that this beeper will only sound in Green/PIC modes, but it also works in P, Av, DEP and camera shake modes. The warning sounds if the shutter speed is at or less than 1/focal length of the lens.
N - On.
Y - Off.
7. Manual-focus operation:
N - Manual-focus adjustment possible by setting focus-mode switch with USM lenses.
Y - Allows manual focus adjustment after autofocus with USM lenses without prior setting. (only in one-shot AF mode)
8. AF assist beam:
N - Enables the body’s AF assist light when there isn’t enough light for the camera to focus. (note one drawback of the 10/10s - it will never use the AF assist light on an external flash unit.)
Y - Camera never uses the camera body’s AF assist light.
9. 1/125 shutter speed lock - flash/Av:
N - Shutter speed set according to ambient lighting. (“subject’s peripheral brightness.”)
Y - Locks AE flash shutter speed at 1/125 sec. (maximum x-sync of the camera)
10. Viewfinder focus mark illumination:
N - On - highlights selected focus marks in red.
Y - Off. (superimposed when the command dial is set at Green or PIC modes and when selecting one focus mark)
11. Depth-of-field preview:
N - Not enabled.
Y - Set to the partial metering button. (note that a: the aperture is stopped down after AF and AE lock and b: when combined with custom function 4, depth of field check does not work in AI Servo AF mode)
12. AE lock (partial metering button):
N - AE lock with partial metering.
Y - AE lock for evaluative metering.
13. Mirror-lock and self-timer:
N - No mirror prefire lock-up.
Y - Mirror locks up prior to the shutter opening, when the shutter release or RC-1 remote controller buttons are pressed. Useful for preventing mirror-induced vibrations from blurring the image on slow shutter exposures.
14. Shutter limitation with anti-shake program:
N - In camera-shake-alert mode, the speed-limit function prevents setting a shutter speed lower than 1/focal length of the lens in use.
Y - No shutter speed limitation.
15. Date back function:
If you have the EOS 10QD with the date back then this custom function does something. Apparently setting this function to Y lets you print both the date and time or something like that.
=============================
自定义功能：
10/10S有14个（10QD有15个）用户自定义设置，佳能称之为“自定义功能”。同时按蓝色和黄色的金属按钮进入自定义功能状态，使用主转盘来切换以数字为代表的功能，按相机后背的圆钮来设置Y（开启）或者N（关闭）。如果你设置了某些CF功能，在LCD上将会显示CF的图标。
........ |
|
/1 
|手机版|Archiver|
咔够网
( 豫ICP备2020028492号-2 )
发表于 2007-10-8 11:48
收藏
分享
淘帖
顶
踩
楼主
真是谢谢楼上大哥的热心帮助！